How to solved Mercedes W212 2011 ESC inperative with Mercedes Star Diagnostic SD Connect Multiplexer

MB Star C4 Mercedes Star Diagnostic Tool support Star Diagnosis and programming. 2017.09 MB Star Diagnosis C4 SD Connect with Xentry Software work for Mercedes car and trucks till July 2017. MB Star Diagnosis SD C4 can work for Mercedes W212 2011 ESC inperative. Below eobdtool.com share guide of how to use the Mercedes Star Diagnostic SD Connect to solved Mercedes W212 2011 ESC inperative.

 

Mercedes Star Diagnostic SD Connect MB Star C4 Multiplexer

mb star C4 sd connect How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

Thread: Mercedes w212 2011 got “ESC inoperative” message, using Eobdtool.com Mercedes Star Diagnostic SD Connect C4 Xentry to pull specific codes firstly and go on repairing, at the last paragraph, there are solution.

Car model and year:

mercedes w212 2011

Issue:

the car shows me “esc inoperative” message then the car become very heavy and it doesn’t take acceleration at all where it is stuck to 15-20 km/h..

i went to a technician and he said it is the throttle sensor, so we got it changed and everything worked fine, after two months the same problem occurred and we got the part changed again, but yesterday the problem appeared again !!

May Caused By:

ESC is electronic stability control not sure why the tech was changing out the throttle and/or position sensor.

ESC inoperative is indicating the traction control is not working. This should be able to tracked to a specific wheel sensor issue, electronic module problem or reflash needed etc.Lots of other possibilities too, steering angle sensor, yaw sensor etc.

How to do?

Take it to an MB dealer and get the car scanned. They should be able to give you a specific MB code and you can go from there. Or did the mechanic scan it and come up with some codes? You can also get some aftermarket scanners, but the ones that do MB specific codes are a bit more than regular OBDII scanners which just do engine and emissions codes, not other sub systems. Your esc inoperative is one of those subsystems

These are all the messages and faults I’m getting

As you can see, I get myself a Mercedes Star Diagnostic SD Connect Xentry from eobdtool.com, These are all the messages and faults I’m getting.

Mercedes Star Diagnostic Tool MB Star C4 SD Connect 1 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011? Mercedes Star Diagnostic Tool MB Star C4 SD Connect 2 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

* voltage of signal 1 of accelerator pedal sensor

* voltage of signal 1 of throttle valve actuator

* voltage of signal 2 of throttle valve actuator

all of these are low voltages around 0.5 where it should be a higher voltage…

 

Mercedes W212 2011 ESC inoperative Solution:

As suggested you pull codes with MB DAS if steadfast on circumventing you can try OEM replacements: TVA 1131410125, ESP CU 2129005906, and OS 0035427018.

– M16/6:

Mercedes Star Diagnostic Tool MB Star C4 SD Connect 3 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

 

– ESP control unit (N30/40) is attached to hydraulic unit, check connection pins before replacing.

– Oxygen sensor 1/bank 2 = left (driver side) front of catalys
Mercedes Star Diagnostic Tool MB Star C4 SD Connect 4 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011? Mercedes Star Diagnostic Tool MB Star C4 SD Connect 5 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011? Mercedes Star Diagnostic Tool MB Star C4 SD Connect 6 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

Mercedes Star Diagnostic Tool MB Star C4 SD Connect 7 1 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

Mercedes Star Diagnostic Tool MB Star C4 SD Connect 8 How to Use SD Connect Solved ESC inoperative of Mercedes w212 2011?

For first time connection of the throttle valve actuator control unit carries out automatically within approx. 60 seconds the following actions:

– determines the emergency running position

– determines lower mechanical stop

– matches the actual value amplifier (signal 1 and 2) in the MESFI [ME] control unit.

– checks the return spring (always takes place when ignition ON) Prerequisite: gear P or N, vehicle stationary, engine OFF, ignition ON, coolant temperature 5 °C to 100 °C and accelerator pedal not operated.

 

The procedure must be activated with Mercedes Star Diagnostic C4 SD Connect , if the throttle valve actuator or the ME-SFI [ME] control unit was replaced.

 

For further questions about Mercedes Star Diagnostic SD Connect MB Star C4 don’t hesitate to contact us

 

Focus On OBD Tool Since 2008

Follow Us:www.facebook.com/eobdtool

Skype:eobdtool02

WhatsApp:(+86)13728823411

Email:[email protected]

Website:www.eobdtool.com

Leave a Reply

Your email address will not be published. Required fields are marked *